Mercruiser #1-DriveTransom/Gimbal Assembly 1978 - 1982 ("Click" here for individual parts, ie;bellows, shift cable, trim cylinders, etc.)

   
page6782.JPG

Quantity

   
page6781.JPG

Quantity

   
18-2614.jpg 18-2614 Outdrive Mounting Gasket Set
$3.95
18-2614
Replaces Mercruiser # 27-64818A1, includes gasket and o'rings to mount outdrive to transom assy.

Quantity

   
18_2100.jpg 18-2100 Gimbal Bearing
$49.95 $39.95 On Sale!
18-2100
Replaces Mercruiser part #30-60794A4. Fits #1/MR/Alpha, Alpha-1 GEN-II and Bravo's.

Quantity

   
18-2751.jpg 18-2751 U-Joint Bellows (with ridge)
$39.95
18-2751
Replaces Mercruiser part#60932A4. Fits all #1/1-R/MR/Alpha-1, Gen-1 outdrives, with "ridge" sn #3469428 and up. Has a "ridge or "bead" of rubber on inside of bellows where hose clamp fastens bellows to gimbal housing and transom plate assy.

Quantity

   
18-2752.jpg 18-2752 U-Joint Bellows (without "ridge")
$39.95
18-2752
Replaces Mercruiser part #36223A2. Fits "EARLY" #1-outdrives, without "ridge", sn # 3443920 & below. Early outdrives, where the U-Joint bellows did not have a "ridge" or "bead" of rubber on inside of bellows where hose clamps fasten bellows to gimbal housing and transom assy. (not very popular, so you must sub this bellows in 18-2601-1 re-seal kit if your application calls for this bellows).

Quantity

   
18-2601-1.jpg 18-2601-1 Transom Reseal Kit
$119.19
18-2601-1
Fits all Mercruiser #1/1-R/MR/Alpha-1, s/n # 6225577 and up. Comes with all bellows, (u-joint, exhaust & shift), water hose, gimbal bearing, clamps, shift arm and outdrive mounting gaskets and o'rings. (order bellows adhesive 18-9031, if needed)

Quantity

   
18-2750.jpg 18-2750 Exhaust Bellows - Double Clamp
$22.95
18-2750
Replaces Mercruiser part#32734A3 & 18654A1. Fits all Mercruiser applications, (Alpha, TRS and Bravo). Has "clamp" on both ends.

Quantity

   
18-2760.jpg 18-2760 Exhaust Tube
$31.95
18-2760
Replaces Mercruiser part#78458A1. Fits all #1/1-R/MR/Alpha and Bravo's. Exhaust bellows non-corragated with one hose clamp.

Quantity

   
18-2753-2 18-2753-2 Shift Cable Bellows
$15.95
18-2753-2
Replaces Mercruiser part#74639. Fits all #1/1R/MR/Alpha and Bravo units. Supplied with "crush" clamp and stainless hose clamp.

Quantity

   
18-2622.jpg 18-2622 Bell Housing Bushing (update) Kit
$29.69
18-2622
Bell Housing Shift Shaft Seal and Bushing Kit, Replaces Mercruiser part # #23-805041A2. Updates older Mercruiser #1, R, MR, Alpha-I to "new" shift shaft seal. Standard on "Early" Mercuiser Alpha-I, Generation-II up to serial number OF094774. Helps to Keep the water out of Unviversal Joint Bellows and Shift Cable.

Quantity

   
18-9031.jpg 18-9031 Bellows Adhesive
$9.45
18-9031
Replaces Mercruiser part#92-86166. Note: Apply bellows adhesive to bellows, let "DRY" to touch and then install bellows.

Quantity

   
18-2158.jpg 18-2248 Shift Cable Assembly (Early-1 drive)
$55.39
18-2248
Replaces Mercruiser # 73723A1, "Foward" installation into "Bell" housing. Does not require support tube.

Quantity

   
18-2161.jpg 18-2161 Shift Arm with Roller
$23.49 $21.15 On Sale!
18-2161
Sierra Shift Arm with Roller, Mercruiser Bell Housing, replaces mercruiser part # 45518A2.

Quantity

   
18-2170.jpg 18-2170 Shift Arm Screw
$1.99
18-2170
Shift Arm Screw for the shift arm 18-2161. Replaces mercruiser part # 10-45590.

Quantity

   
1239116.jpg 12-39116 Nylon Washer for Shift Arm Assembly
$1.09
1239116
Nylon Washer for Shift Arm Assembly.

Quantity

   
45589a32.JPG 45589A3 Stainless Steel Shift Shaft in Bell Housing
$43.49 $35.95 On Sale!
18-2169
Sierra Replacement Stainless Steel Shift Shaft in Bell Housing, replaces Mercruiser part # 45589A3.

Quantity

   
18-2142.jpg
18-2142 Trim Cylinder $295.19 18-2142
Replaces Mercruiser part#45706A14. Trim hoses attach to the "FRONT" of cylinder, next to each other.

Quantity

   
18-2103.jpg 18-2103 Hydraulic Trim Hose
$23.95
18-2103
Hose from Connector to trim Cylinder, with two 1/8" fittings and 14" in length.

Quantity

   
GLM21310F GLM21310 Shaft Pivot Pin Kit (Front)
$39.95
GLM21310
Shaft Pivot Pin, 10-1/2". Located closest to transom, (front pin). Kit comes complete with pin, bushings, washers and nuts.

Quantity

   
GLM21390R GLM21390 Shaft Pivot Pin Kit (Rear)
$40.95
GLM21390
Shaft Pivot Pin, 7-1/2". Kit comes complete with pin, bushings, nuts and washers. Rear pin, Located above the propeller or furthest from the boat.

Quantity

   
473472.jpg 47347 Hydraulic Trim Line Connector
$30.29
47347
Hydraulic Trim Line Connector, under transom plate assembly on outside of boat.

Quantity

   
18-0342 18-0342 Gasket for connector (47347)
$1.29
18-0342
Gasket for trim hose connector part # 47347.

Quantity

   
18-2701.jpg 18-2701 Power Trim Bushing
$3.95
18-2701
Replaces #23-89574, Fits 120/260 Drive Units(s/n 6225276 & down)

Quantity

googlepay.jpg

Marineengineparts.com & Partman.com are wholly owned subsidiaries of Lighthouse Marine Supply & Lighthouse Marine Distributors, Inc
Partman & Partman.com are both registered trademarks of lighthouse Marine Distributors, Inc., Not responsible for typographical errors. Some merchandise may be limited in supply or available only by special order. Pictures are for illustrations purposes only, Prices are subject to change without notice.
29 Edgar Avenue - Riverhead, NY 11901 - toll free: 800-382-9335 - p: 631-722-5700 - fax: 631-722-5719 or Email: sales@partman.com