Engine & Transmission Mounts
|
Crusader 97926 Engine Mount - Single$43.73 CRU97926 Crusader 97926 Engine Mount "Single", with 1" Trunnion Shaft. NOTE: For older applications using 7/8" Trunnion Shaft, you must drill engine mounted bracket to accept new 1" trunnion shaft. |
Crusader 97905 Engine Mount - Dual$107.81 CRU97905 Crusader 97905 Engine Mount "Dual", with 1" Trunnion Shaft. NOTE: For older applications using 7/8" Trunnion Shaft, you must drill engine mounted bracket to accept new 1" trunnion shaft. |
97938 Crusader Support Bracket - FRONT MOUNT$51.75 CRU97938 Front Engine support bracket for Crusader GM (Chevy) engines. Accommodate's CRU97926 and CRU97905 mount's with 1" shaft. |
97917 Crusader Support Bracket - Rear/Transmission$71.81 CRU97917 Rear Engine support bracket (Bolts to Transmission)direct replacement for Crusader engine's. Accommodate's both the CRU97296 single mount and CRU97905 dual mount with 1" shaft. |
BARR MC-8-66418 Engine Support GM (Chevy) V-6 and V-8 Engines BARMC-8-66418 BARR MC-8-66418 Engine Support GM (Chevy) V-6 and V-8 Engines. Front engine support(s) Sold as a pair, include's steel shaft (trunnion), (Has 3/4" hole) to connect to stringer mount. (Such as part # BUSDF-216). SOLD as PAIR (@2). |
Bushing Inc. DF-216 Engine Mount With 3/4" SHAFT
BUSDF-216 Bushing Inc. DF-216 Engine Mount With 3/4" SHAFT Adjustable Vertically to facilitate engine prop shaft alignment. The rubber element of the mount will withstand temperature extremes and exposure to salt, oil and grease. Holds loads UP TO 275 pounds. NOTE "stud" is 3/4"-18 thread. Replacement for most current I/O and inboard gasoline engine applications up to 7.4-Liter. (Replaces Mercruiser part #'s 66284A2 and 814263A1). Base is 5-1/4" x 2-5/8". There is 2-3/8" from bottom of mount to lowest adjustment point. and 4-7/8" from bottom of mount to top of 3/4"-18 stud. (4" mounting holes center to center). Note: Do not use with Diesel engines. |
Barr 53-5011 Rear Engine Mount -Complete (Borg Warner Transmissions)BAR53-5011 Barr 53-5011 Rear Engine Mount -Complete (Borg Warner Transmissions) and other inboard transmissions. Direct Replacement for most Chrysler, Pleasurecraft/PCM, and Indmar motors. |
Barr 8-0008 Engine Mount (90° Base) 3/4" StudBAR8-0008 Barr 8-0008 Engine Mount (90° Base) 3/4" Stud. Each mount holds loads to 350 pounds. Base is 5" long x 1-3/4" wide. Vertical flange is 1-1/2" high. 2-11/16" from bottom of mount to lowest adjustment point. 4-1/2" from bottom of mount to top of 3/4-16 stud. |
Barr 8-0001 Engine Mount with- 5/8" Stud BAR8-0001 Barr 8-0001 Engine Mount with- 5/8" Stud. Adjustable Vertically to facilitate engine prop shaft alignment. The rubber element of the mount will withstand temperature extremes and exposure to salt, oil and grease. Holds loads 200 pounds. Base measures 5" long x 2-3/4" wide. There is 2-3/8" from bottom of mount to lowest adjustment point and 4-1/4" from bottom to highest point 5/8"-18 stud. USED ON SMALLER GASOLINE INBOARD APPLICATIONS (atomic-4 etc). |
Bushings inc.DF-206 Engine Mount 5/8" Shaft
BUSDF-206 Bushings inc. Engine Mount 5/8" Shaft. 5" mounting foot with 4" bolt centers and 5/8" center stud. Holds loads up to 200-lbs. Used on early I/O and inboard gasoline engine applications. Base is 5-1/4" x 2-5/8". NOTE: 2-3/8" from bottom of mount to lowest adjustment point. 4-1/4" from bottom of mount to top of 5/8"-18 stud. Note: DO NOT use with Diesel engines. |
Bushings Inc. DF238-M1 Diesel Engine MountBUSDF238-M1 Bushings Inc. DF238-M1 Diesel Engine Mount. Adjustable Vertically to facilitate engine prop shaft alignment. The rubber element of the mount will withstand temperature extremes and exposure to salt, oil and grease. Holds loads up to 550-lbs. Base is 6-1/2" x 3-3/8". 2-7/10" from bottom of mount to lowest adjustment point. 5" from bottom of mount to top of 3/4-18 stud. |
Barr 8-0002 Engine Mount BAR8-0002 Barr 8-0002 Engine Mount. Double Bushing mount. Increased capacity for Diesel and Heavy-duty applications. Adjust vertically up to 1". 550 pound capacity per mount. Base is 8-1/4" x 2" wide. 3-1/8" from bottom of mount to lowest adjustment point. 5-5/8" from bottom of mount to top of 5/8-18 stud. |
Bushings Inc. DF-242 Engine Motor MountBUSDF-242 Bushings Inc. DF-242 Engine Motor Mount. 2-Mountings in same casting. Increased capacity for Diesel and Heavy-duty applications. 650-Lbs-capacity. Base is 12" x 3-3/8" wide. 2-1/2" from bottom of mount to lowest adjustment point. 4-1/2" from bottom of mount to top of 3/4-16 studs. |
Chrysler 4417224 Engine Mount and TrunnionNote: DISCONTINUED, order part # GR3561-3N (complete mount assembly). Note: if you have ability to fill and then re-drill stringer mounting holes, you could use part # BUSDF-216, which has 4" on center mounting bolts, compared to Chrysler 3-1/2" on center mounting bolts. 
 |
Chrysler GR3561-3N Front Engine Mount AssemblyCHYGR3561-3N Chrysler GR3561-3N Front Engine Mount Assembly. Chrysler complete front mount assembly. Comes complete with front engine support as shown. Chrysler Inboard engine models LM318, 360 and 440. Sold per mount assembly. 3-1/2" center to center mounting bolt holes. |
|
|
 |
local: (631)-722-5700
Partman & Partman.com are both registered trademarks of lighthouse Marine Distributors, Inc., Not responsible for typographical errors. Some merchandise may be limited in supply or available only by special order. Pictures are for illustrations purposes only, Prices are subject to change without notice.
29 Edgar Avenue - Riverhead, NY 11901 - toll free: 800-382-9335 - p: 631-722-5700 - fax: 631-722-5719 or Email: sales@partman.com