Mercury / Mercruiser - Special Tools
|
GIMBAL BEARING PULLER PROFESSIONALBJMGBP-1-PL This gimbal bearing puller is the easiest way to remove the gimbal bearing from the housing for replacement with a new 18-2100 gimbal bearing. This tool insures that no damage will be done to the housing from uneven pulling or impacts. |
||
PRESSURE TESTER (GEARCASE)STNS-34 Heavy duty pressure tester, can be used for testing gearcases, outdrives, manifolds, risers, ect. Ready for gearcases and outdrives. Manifolds and risers will require additional adaptors and accessories. |
||
|
VACUUM TESTER (GEARCASE) STNV-34 Heavy duty vacuum tester, can be used for testing gearcases, outdrives, manifolds, risers, ect. Ready for gearcases and outdrives. |
||
CDI 551-34PV PRESSURE AND VACUUM TESTERCDI551-34PV New from CDI 551-34PV, vacuum and pressure tester all-in-one, (1) tool does both pressure and vacuum testing for Sterndrive's and Outboard lower units. |
||
MERCRUISER STERNDRIVE ENGINE ALIGNMENT TOOL 18-444218-4442 MERCRUISER STERNDRIVE ENGINE ALIGNMENT TOOL 18-4442. Used to verify engine alignment with the gimbal bearing on all MC-1, R-MR, Alpha One, Alpha-1 Gen-II and Bravo Sterndrives. (Note: for older TRS Sterndrives must order merc tool 91-805475A1). |
||
MERCRUISER HINGE PIN TOOL 18-986118-9861 MERCRUISER HINGE PIN TOOL BY SIERRA 18-9861, Removes and installs "Hinge Pins, prt#77321", on bell housing for mercruiser drive units. Caution do not over torque tool or hinge pin, use suitable penetrating oil to remove hinge pin and when installing hinge pin torque to manufacturers specifications. |
||
LOWER SHIFT CABLE NUT REMOVER 18-9806E18-9806E 18-9806E This tool removes shift cable (nut) without interfearing with nylon cable guide, a must for all do it yourselfer's and mechanics. |
||
DRIVE SHAFT BEARING RETAINER WRENCH 18-984218-9842 18-9842 TOOL, Removes and installs threaded bearing retainer on alpha drive units. |
||
TOOL MERC BELLOWS EXPANDER 18-984718-9847 18-9847 BELLOWS EXPANDER TOOL installs exhaust bellows on MC-I, R-MR,Alpha One, Bravo One,Two and three and Blackhawk drive units. |
||
BEARING CARRIER RETAINER TOOL 18-980918-9809 18-9809 TOOL Loosens and tightens bearing carrier nut (retainer) on Bravo Two drives. Replaces Mercruiser # 91-17257 |
||
BEARING RETAINER WRENCH 18-980318-9803 BEARING RETAINER WRENCH 18-9803, is used to remove and install driveshaft bearing retainers on MC-I, R-MR, Blackhawk, Bravo and all Alpha Units. |
||
|
BEARING CARRIER RETAINER WRENCH 18-9858 18-9858 18-9858 Removes and installs bearing carrier retainer nuts on Bravo One and Two, MC-1, R-MR, Alpha One, Alpha One Gen Two, TRS drive units and outboards. |
||
SHIFT SHAFT BUSHING TOOL 18-981718-9817 18-9817 TOOL, Removes and installs the shift shaft bushing in the gear case of; MC-1,-MR, and Alpha One Drive Units. |
||
PINION GEAR SHIMMING TOOL 18-985318-9853 18-9853, Measures pinion height of MC-1, R-MR, Alpha One and Alpha One Generation Two drive units. Replaces merc. # 91-56048T |
||
Sierra 18-9844 Tool install Bravo Water Inlet Hose Retainer$22.49 18-9844 Sierra 18-9844 Tool install Bravo Water Inlet Hose Retainer, same as Mercruiser tool # 91-443579. |
||
Sierra 18-9870 Tool installs aluminum sleeve18-9870 Sierra 18-9870 Tool installs aluminum sleeve in the u-joint bellow on Alpha Gen-II and Bravo sterndrives, replaces mercruiser # 91-818162. |
||
18-9801 DVA MULTI-METER18-9801 This is a universal "DVA" multi-meter which can be helpful in diagnosing AC, DC, Volt and AMP values and Ohms readings. Analog display, can be used on many marine engines or electrical systems. |
||
|
||
PROP WRENCH, 91-859046M4 MERCURY$14.99 91859046M4 Mercury prop Wrench, 91-859046M4, 1-1/16" - (28mm). Mercury / Mariner 75, 90, 100, 115, 125, 135, 150, 175, 200, 225, 250hp. |
Partman & Partman.com are both registered trademarks of lighthouse Marine Distributors, Inc., Not responsible for typographical errors. Some merchandise may be limited in supply or available only by special order. Pictures are for illustrations purposes only, Prices are subject to change without notice.
29 Edgar Avenue - Riverhead, NY 11901 - toll free: 800-382-9335 - p: 631-722-5700 - fax: 631-722-5719 or Email: sales@partman.com