Mercruiser Alpha-1Transom/Gimbal Assembly 1983 - 1990 ("Click" here for individual parts, ie;bellows, shift cable, trim cylinders, etc.)
|
|
|
18-2619-1 Outdrive Mounting Gasket Kit18-2619-1 Replaces Mercruiser part#27-64818A3. Fits All Alpha-1 (1983 and newer) and Alpha-1, GEN-II with internal gear lube monitor. |
Sierra 18-2100 Gimbal Bearing (30-60794A4)18-2100 Sierra 18-2100 Gimball Bearing, Replaces Mercruiser part #30-60794A4. Fits Mercruiser #1/MR/Alpha from 1974 to 1997 and Early Bravo Sterndrives. Also replaces OMC part # 983937 AND 3853807, Fits OMC Cobra and Volvo-Penta SX- Sterndrives. |
18-2751 U-Joint Bellows (with ridge)$39.95 18-2751 Replaces Mercruiser part#60932A4. Fits all #1/1-R/MR/Alpha-1, Gen-1 outdrives, with "ridge" sn #3469428 and up. Has a "ridge or "bead" of rubber on inside of bellows where hose clamp fastens bellows to gimbal housing and transom plate assy. |
18-2753-2 Shift Cable Bellows$15.95 18-2753-2 Replaces Mercruiser part#74639. Fits all #1/1R/MR/Alpha and Bravo units. Supplied with "crush" clamp and stainless hose clamp. |
18654A1 Exhaust Bellows - Double Clamp18-2750 Sierra 18-2750 exhaust bellows. Replaces Mercruiser part #'s 32734A3 & 18654A1. Fits all Mercruiser applications, (Alpha, TRS and Bravo). Has "hose clamp" on both ends. |
Sierra 18-2760 Exhaust Bellows (Tube-Type) Single Clamp18-2760 Sierra 18-2760 Exhaust Bellows (Tube-Type) Single Clamp. Replaces Mercruiser part # 78458A1. Fits all #1/1-R/MR/Alpha and Bravo's. Exhaust bellows non-corragated with one hose clamp. (Sometimes reffered to as "Cheater" bellows). |
Sierra 18-2601-1 Transom Reseal Kit18-2601-1 Sierra 18-2601-1 Transom Reseal Kit, Fits all Mercruiser #1/1-R/MR/Alpha-1, s/n # 6225577 and up. Comes with all bellows, (u-joint, exhaust & shift), water hose, gimbal bearing, clamps, shift arm and outdrive mounting gaskets and o'rings. (order bellows adhesive 18-9031, if needed). |
Sierra 18-8205 Transom Re-seal Kit (with exhaust "tube")18-8205 Sierra 18-8205 Transom Re-seal Kit (with exhaust "tube"). Kit, Transom Re-seal, All Alpha-I, includes all bellows (gimbal, exhaust and shift bellows), gimbal bearing, water hose, outdrive mounting gasket and o-rings. NOTE: exhaust bellows in this kit is "tube" type, held on with only hose clamp on boat side, will have "louder" exhaust sound then exhaust bellows with clamps on both ends). |
Sierra 18-2190 Alpha Shift Cable (Intermidiate Housing)18-2190 Sierra 18-2190 Alpha Shift Cable (Intermidiate Housing). Replaces Mercruiser part #'s 19543A4 and 865436A02. Fits Mercruiser #1 drives s/n #6225577 & up. For "Aft" installation into "bell" housing. For use in applications using core wire with armored strand construction. (No support tube) 63" conduit with hardware package. |
Sierra 18-2603 Alpha Shift Cable Kit w/Shift Bellows and Mounting Gaskets18-2603 Sierra 18-2603 Alpha Shift Cable Kit w/Shift Bellows and Mounting Gaskets, Replaces Mercruiser part #19543T1. Complete shift cable kit for Alpha GEN-1 and GEN-II's. Complete with shift cable bellows and mounting gaskets. |
Mercruiser 865436A02 LOWER SHIFT CABLE (OEM) $75.00 865436A02 Mercruiser 865436A02 LOWER SHIFT CABLE (OEM), Made by Mercruiser, Aft Entry Lower shift cable for all Mercruiser Alpha-1 and GEN-II. Original Equipment Mercruiser Shift Cable. |
18-9031 Bellows Adhesive$9.45 18-9031 Replaces Mercruiser part#92-86166. Note: Apply bellows adhesive to bellows, let "DRY" to touch and then install bellows. |
18-3601 Water Intake Hose (5/8" ID)18-3601 Replaces: 32-32461, 13-7/8" Length - 5/8" I.D., For: MCI, R, MR, Alpha I. 18-3601 Water Intake Hose (5/8" ID). |
|
18-3602 Water Intake Hose (3/4"-ID) $9.49 18-3602 Replaces: 32-41725-33, 13-7/8" Length - 3/4" I.D., For: MR, Alpha I, Gen II |
18-2622 Bell Housing Bushing (update) Kit$29.69 18-2622 Bell Housing Shift Shaft Seal and Bushing Kit, Replaces Mercruiser part # #23-805041A2. Updates older Mercruiser #1, R, MR, Alpha-I to "new" shift shaft seal. Standard on "Early" Mercuiser Alpha-I, Generation-II up to serial number OF094774. Helps to Keep the water out of Unviversal Joint Bellows and Shift Cable. |
12-35935 Washer for Out Drive Mounting Stud$1.18 1235935 Washer for Out Drive Mounting Stud. |
11-134391 Nylon Lock Nut 7/16-20BJM11134391 Nylon Lock Nut 7/16-20, Mercruiser part # 11-134391. |
98825A4 Hydraulic Trim Line Connector Assembly$73.64 98825A4 Hydraulic Trim Line Connector Assembly. |
77123 Bell Housing Hinge Pin$21.28 77123 Bell Housing Hinge Pin, use the "MERCRUISER HINGE PIN TOOL, prt#18-9861",for installation and removal of pin. |
18-2161 Shift Arm with Roller18-2161 Sierra Shift Arm with Roller, Mercruiser Bell Housing, replaces mercruiser part # 45518A2. |
18-2170 Shift Arm Screw$1.99 18-2170 Shift Arm Screw for the shift arm 18-2161. Replaces mercruiser part # 10-45590. |
12-39116 Nylon Washer for Shift Arm Assembly$1.09 1239116 Nylon Washer for Shift Arm Assembly. |
45589A3 Stainless Steel Shift Shaft in Bell Housing18-2169 Sierra Replacement Stainless Steel Shift Shaft in Bell Housing, replaces Mercruiser part # 45589A3. |
41802 Exhaust "Y"-Pipe toTransom Assembly Seal$8.13 41802 Exhaust "Y"-pipe to Transom Assembly Seal. Only can be replaced by removing engine from boat. |
18-2116 Trim Line "Short" (Port and Starboard) 32-99904$29.95 18-2116 Replaces Mercruiser part#32-99904. Fits Alpha cylinder #14035A3, 14034A3, 98704A3 & 98703A2 and Bravo cylinder #'s 98704a17 & 98703A26. These are the trim lines closest to the boat on the front of the cylinders. Short and used on both port and starboard sides. |
18-2426 Power Trim Cylinder Port (98703A3)$295.95 18-2426 Replaces: 98703A3, For: R/MR/ALPHA (Port). Note:look on the side of cylinder for casting #98703, 98703-1. |
18-2137 Trim Line (PORT) 32-99903$34.95 18-2137 Replaces Mercruiser part#32-99903. Fits Alpha cylinder #98703A3 and Bravo cylinder #98703A26. (port side) |
18-2427 Power Trim Cylinder Starboard (98704A3)$295.95 18-2427 Replaces: 98704A3, For: R/MR/ALPHA (Starboard). Note:look on the side of cylinder for casting #98704, 98704-1. |
18-2136 Trim Line -(Starboard) 32-99902$34.95 18-2136 Replaces Mercruiser part#32-99902. Fits Alpha cylinder with casting #98704 and Bravo cylinder #98704A17. (Starboard side) |
18-2421 Power Trim cylinder Port (145035A3)$319.20 18-2421 Replaces: 14035A3, For: R/MR/ALPHA (Port). Note:Look on side of trim cylinder for casting #14035-1. |
18-2115 Trim Line (Port) 32-99903-1$34.95 18-2115 Replaces Mercruiser part#32-99903-1. (Port side), Fits Alpha trim cylinder with casting #14035. |
18-2420 Power Trim Cylinder Starboard (14034A3)$319.19 18-2420 Replaces: 14034A3, For: R/MR/ALPHA (Starboard). Note:look on the side of cylinder for casting #14034-1. |
18-2114 Trim Line (Starboard) 32-99902-1$34.95 18-2114 Replaces Mercruiser part#32-99902-1. (Starboard), Fits Alpha trim cylinder casting #14034. |
MALLORY 9-77000 POWER TRIM BUSHINGSMAL9-77000 MALLORY 9-77000 POWER TRIM BUSHINGS, 4-PACK, Replaces Mercruiser part # 23-99291, 23-99291T, Sierra # 18-2702, 18-2702-1 and 18-2702-04. Order quanity of (1), you will recieve (4) bushings. Fits Later Mercruiser R/MR/Alpha-1 Sterndrives, from serial # 6225277 and up, prior to Alpha Gen-II, measures 5/8" ID. X 1-3/4" OD. |
805320A03 Trim Limit and Trim Sender Kit Sierra part # 18-763318-7633 New from Sierra 18-7633 Mercruiser Replacement Trim limit and trim sender kit for all Alpha and Bravo units. Replaces Mercruiser part # 805320A03. |
local: (631)-722-5700
Partman & Partman.com are both registered trademarks of lighthouse Marine Distributors, Inc., Not responsible for typographical errors. Some merchandise may be limited in supply or available only by special order. Pictures are for illustrations purposes only, Prices are subject to change without notice.
29 Edgar Avenue - Riverhead, NY 11901 - toll free: 800-382-9335 - p: 631-722-5700 - fax: 631-722-5719 or Email: sales@partman.com